Erklärung der Leuchtdioden auf der

Erklärung der Leuchtdioden auf der GSUBezeichnung LED ist ein LED blinktStandby Turbine wird gestartet bzw.hochgefahren ---Ignition Glühkerze ist EIN ---Pump running Kraftstoffpumpe läuft Glühkerze defekt(Unterbruch)OK Turbine im Reglerbetrieb, a) Wenn Turbine läuft:Zulässige AbgastemperaturTurbinendrehzahl kann über überschritten.den Gasschieber vorgegeben b) Wenn Turbine Aus:werden. Steuerung befindet sich im „Slow-down“ Zustand“.Sonderfunktionen:Wenn die Leuchtdioden „Standby“ und „OK“ gleichzeitig blinken ist der Versorgungsakku nachzuladen.MenüstrukturAlle Einstellparameter sind in sogenannten Menüs abgelegt und können mittels der GSU angezeigt bzw. verändert werden.Die zur Verfügung stehenden Menüs sind: RUN- Menü INFO- Menü MIN/MAX-Menü STATISTICS- Menü RC-Check- Menü GPS-Menü (falls aktiviert) Test Menü Limits-MenüAnwahl eines MenüsDie verschiedenen Menüs können entweder direkt mit den entsprechenden Tasten auf der GSU angewählt ( Hotkeys) werden, oder durch Drücken und Halten der Taste „Select Menu“. Mit den +/- Tasten kann dann das gewünschte Menü ausgewählt werden.Die verschiedenen Optionen innerhalb eines Menüs können durch alleiniges Drücken der +/- Tasten angezeigt/durchgeblättert werden.Verändern von Werten/Parametern in einem MenüUm einen angezeigten Wert zu verändern wird die Taste „Change Value / Item“ gedrückt gehalten, mit den +/- Tasten kann dann der Wert verändert werden.

結果 (英文) 1:

Explanation of the LEDs on the GSU
Description LED is on LED flashes
Standby turbine is started or
booted ---
Ignition glow plug is ON ---
Pump running Fuel pump running glow plug defective
(interruption)
OK turbine controller operation, a) If turbine is running:
Permissible exhaust gas temperature
turbine speed can be exceeded.
set the throttle valve b) If turbine Germany
be. Controller is in "Slow-down" state ".
Special functions:
When the "Standby" and "OK" flash simultaneously the supply battery is recharged.
menu structure
All setting parameters are stored in a series of menus and can be displayed by means of the HSE or changed.
The available menus are:
 RUN menu
 INFO menu
 MIN / MAX menu
 STATISTICS menu
 RC-Check menu
 GPS menu (if enabled)
 Test menu
 Limits menu
Selecting a menu
that ( hotkeys) are various menus can either be selected directly with the corresponding buttons on the GSU, or by pressing and holding the "Select menu" button. Use the +/- keys to select the desired menu can then be selected.
The different options in a menu can be displayed by simply pressing the +/- keys / to scroll through.
Changing values / parameters in a menu
to change order an indicated value is the button pressed "Change Value / Item", the value can then be changed with the +/- keys.

結果 (英文) 2:

Explanation of light-emitting diodes at the GSU
Name LED is an LED flashing
Standby turbine is started or
---
Ignition Glow Plug is ONE ---
Pump running fuel pump runs glow plug defective
(Interruption)
OK Turbine in controller mode, a) When turbine is running:
Permissible exhaust gas temperature
Turbine speed may exceed.
the gas slider predetermined b) If turbine off:
Be. control is in the "slow-down" state".
Features:
If the light-emitting diodes "Standby" and "OK" flash at the same time, the supply battery must be recharged.
Menu
All setting parameters are stored in so-called menus and can be displayed or changed using the GSU.
The available menus are:
• RUN menu
INFO menu
MIN/MAX menu
STATISTICS menu
RC-Check-Menu
GPS menu (if activated)
Test menu
• Limits menu
Selecting a menu
The different menus can be selected either directly with the corresponding buttons on the GSU (hotkeys) or by pressing and holding the "Select Menu" key. The +/- buttons can then be used to select the desired menu.
The various options within a menu can be displayed/scrolled through by pressing the +/- buttons alone.
Changing values/parameters in a menu
To change a displayed value, the "Change Value / Item" button is pressed, with the +/- keys the value can then be changed.

結果 (英文) 3:

Explanation of the LEDs on the GSU
Name LED is a LED flashing
Standby Turbine is started or
the ---
Ignition bulb is a---
Pump running fuel pump running bulb defective
(Interruption)
OK Turbine in controller operation, a) When the turbine is running:
Allowed exhaust temperature
Turbine speed may exceed.
(b) If turbine off:
and. Control is in slow-down mode.
Special:
If the LEDs "standby" and "OK" flash simultaneously, the supply battery shall be recharged.
Menu
All settings are stored in so-called menus and can be displayed via the GSU or be changed.
The available menus are:
RUN Menu
INFO Menu
MIN/MAX Menu
STATISTICS Menu
RC Check Menu
GPS menu (if enabled)
Test Menu
Limit Menu
Select a menu
The different menus can be selected either directly with the corresponding keys on the GSU (61664hotkeys), or by pressing and holding the "Select Menu" button. The +/- keys can then be used to select the desired menu.
The various options within a menu can be displayed/browsed by pressing the +/- keys alone.
Change values/parameters in a menu
To change a displayed value, the "Change Value/ Item" button is pressed, with the +/- keys the value can then be changed.